|
www.borepumps.com.au
Current Category
Control images
|
Bore Cap & Fittings for Manual Control - 25mm - To 1,600 kPa
The fittings kit for a bore pump that is simply to be operated manually by turning the power on and off is pretty simple and includes the cast iron or optional stainless steel bore cap, Nyglass fittings, pressure gauge and outlet isolating valve. The fittings are supplied pre-asembled for easy on-site installation. this particular unit is shown with 32mm fittings and reduced to a 25mm ball valve and would be quite suitable for any flow rate up to around 30 litres per minute with practically no pressure loss through the fittings.
|
|
Price:
|
|
|
Bore Cap & Fittings for Manual Control - 32mm - To 1,600 kPa
The fittings kit for a bore pump that is simply to be operated manually by turning the power on and off is pretty simple and includes the cast iron or optional stainless steel bore cap, Nyglass fittings, pressure gauge and outlet isolating valve. The fittings are supplied pre-asembled for easy on-site installation. This particular unit is shown with 32mm fittings and a 32mm ball valve and would be quite suitable for any flow rate up to around 50 litres per minute with practically no pressure loss through the fittings.
|
|
Price:
|
|
|
Bore Cap & Fittings for Pressure Switch Control
This is a heavy duty fittings kit including a pressure tank and Telemecanique 1 - 1,200 kPa automatic pressure switch, pressure gauge and main and secondary isolating outlet ball valves. The fittings are supplied pre-assembled and packed in their own carton ready for site installation. This unit is suitable for controlling any single phase submersible bore pump to 3.7 kW directly off the pressure switch contacts.
|
|
Price:
|
|
|
Bore Cap & Fittings for Pressure Switch Control with F28 Protection Controller
The F28 version of the pressure switch control unit is always recommended where there is any chance at all that the pump could run out of water. The F28 switch allows the operator to match the output of the pump to the inflow into the bore and even turn the pump off for a specific time to allow the bore time to refill. The F28 will also turn the pump off should it actually run out of water. An excellent system that provides a high level of control and protection.
|
|
Price:
|
|
|
Bore Cap & Fittings for Automatic WHI Controller
Our WHI automatic controller system suits all single phase pumps of 0.37, 0.55, 0.75 and 1.1 kW with a closed head of less than 10 Bar or 100m. The WHI provides automatic ON/OFF operation in response to pressure drop and flow while also providing some protection against running the pump dry. Terrific for a smaller bore when you only need a flow of less than 50 litres per minute into a tank or an irrigation system. Again, this unit is supplied pre-assembled and tested ready for site installation.
|
|
Price:
|
|
|
Bore Cap & Fittings with F28 Protection Controller Only
This has got to be the ultimate in bore pump controllers. The F28 is a quad timer and flow switch all in one unit. It allows you to start the pump on time, run for as long as required and then stop. If the bore runs out of water, the flow switch turns the pump off and, waits for a specific time before trying to start the pump again. Supplied all pre-wired and assembled ready for site installation. You can also program the timer function so that if you have a bore that has a low yield, you can start, run, stop, wait and start again. It is also the perfect method of controlling a pump supplying a stock watering system as you can eliminate cycling.
|
|
Price:
|
|
|
Bore Cap & Fittings for Manual Control - 40mm - To 1,600 kPa
The fittings kit for a bore pump that is simply to be operated manually by turning the power on and off is pretty simple and includes the cast iron or optional stainless steel bore cap, Nyglass fittings, pressure gauge and outlet isolating valve. The fittings are supplied pre-asembled for easy on-site installation. This particular unit is shown with 50mm fittings and reduced to a 40mm ball valve and would be quite suitable for any flow rate up to around 80 litres per minute with practically no pressure loss through the fittings.
|
|
Price:
|
|
|
Bore Cap & Fittings for Manual Control - 50mm - To 1,600 kPa
The fittings kit for a bore pump that is simply to be operated manually by turning the power on and off is pretty simple and includes the cast iron or optional stainless steel bore cap, Nyglass fittings, pressure gauge and outlet isolating valve. The fittings are supplied pre-asembled for easy on-site installation. This particular unit is shown with 50mm fittings and a 50mm ball valve and would be quite suitable for any flow rate up to around 100 litres per minute with practically no pressure loss through the fittings.
|
|
Price:
|
|
|
